All the reasons why the scooter does not pick up speed and revolutions

Let's imagine this situation. You bought a new 49.9cc scooter and easily accelerate it to 60 km/h, enjoying it. But over time, you notice that you cannot accelerate it to maximum speed. Don't panic right away. The sooner you notice this, the easier and cheaper the repair will be.

If the scooter's engine lacks power, do a visual check. To do this, start the scooter and add a little gas to observe. If the engine revs poorly, there may be several reasons:

clogged air filter;
the spark plug is faulty;
clogged gas filter or carburetor;
clogged muffler;
faulty starting enrichment;
clogged or leaking rubber gas and air pipes leading to the gas valve and carburetor.
transmission malfunction;
piston wear;

Let's look at the reasons and start with the simplest. After each action, it is necessary to start the engine and check it for changes in operation.

1. First, check and clean the air filter. Many people do not pay special attention to this detail, and this is a big mistake. The filter is one of the most important parts of the scooter and requires special care. How to clean the air filter, read the article Air Filter Maintenance .

2. If this does not help, then check the spark plug. We unscrew the spark plug and check for the presence of a spark. Reasons for lack of spark:

faulty or dirty spark plug;
broken or shorted wiring;
broken or “shorted” ignition coil;
broken or “shorted” inductive ignition sensor;
faulty ignition switch;
faulty generator;

We also pay attention to its color and the presence of soot. A normal spark plug has the color of deposits on the insulator (the skirt of the central electrode) light brown or coffee; soot and deposits are minimal. Complete absence of oil traces. Moderate electrode burnout. If the spark plug has a large layer of carbon deposits, a different color, or pronounced traces of oil, then this indicates a malfunction of the spark plug, a malfunction of the piston system or the fuel system. It is better to replace the spark plug with a new one and check the engine again for speed. There are several reasons for light failure:

faulty or dirty spark plug;
over-enriched mixture;
inappropriate spark plug heat rating;
problems with the piston - it splashes with oil

3. The next step is to check the compression in the engine cylinder. If there is no compression or low (4-6 atm), then here are several reasons:

faulty reed valve - for 2t engines;
leakage through the crankcase, for example through the crankshaft seals - for 2t engines;
burnt or loose valves - for 4t engines;
torn cylinder head gasket;
burnt or worn piston or cylinder, or rings;
crack in the cylinder head.

If we have determined the cause, then we begin the repair. Well, if the cylinder is in complete order, then proceed to the next step.

4. Adjust the carburetor and check the entire fuel system for leaks. For information on how to adjust the carburetor, see the article Adjusting the carburetor.

5. The muffler may be clogged and needs to be cleaned. A clogged muffler causes a lot of problems; usually, after cleaning, the scooter becomes unrecognizable.

6. Another possible reason is wear of the variator belt. If necessary, you need to change the variator belt and it is advisable to replace the variator rollers. For more information on replacing the belt, read the article Replacing the variator belt on a scooter .

Troubleshooting

What to do if the hoverboard does not charge? Here are some simple tips for troubleshooting:

To remove the bottom panel, use a screwdriver or screwdriver with the appropriate bit. This will allow you to get to the inside of the vehicle and try to find the problem of poor charging.

The side of the scooter with the charging port is the area you need to work on. Be careful during disassembly. Do not lose screws or washers, or use a drill to remove screws or bolts that will not come loose. There will be several wires directly on the inside of the plastic cover you just unscrewed.

They are responsible for charging the hoverboard: they connect the charger ports and the lithium-ion battery. The other wire line goes to the motherboard. You can temporarily disconnect it to avoid an unexpected power surge (only if the board is disconnected by a connector). If the wires are soldered, it is better not to touch them.

Is there blackening of the wire or oxidation of the contacts, is there a large amount of dust present? This may well be the reason for the device to not work correctly. Accumulations of dust must be removed, damaged wires must be replaced, and contacts must be cleaned to a metallic shine.

Having completed such an impromptu diagnosis, screw the cover back to the hoverboard, tightening all the removed bolts one by one.

They will help you make diagnostics more efficiently and without risk to the scooter. True, it is no longer free.

If, despite all this, your scooter continues to work incorrectly, you will need to contact the manufacturer and request repair instructions. In the worst case, the hoverboard will have to be sent back to the manufacturer under warranty. It may be that the device was initially faulty and will be replaced under warranty. It often happens that a newly purchased hoverboard does not charge.

Motorcyclist

The most common reason is a worn clutch, then a worn variator belt, worn variator rollers, a worn clutch spring, and the variator itself can also be worn out. The most dangerous thing is examining and replacing the variator. On most scooters, the nut that secures the CVT is unscrewed clockwise; Do not unscrew it with a bolt gun under any circumstances, because you can break the crankshaft thread (then you get a lot of money: crankshaft from 3000 rubles + work to replace it with engine overhaul)

There are, but less frequently, other causes of breakdowns. In the event of such a breakdown, getting into the engine is the last thing; at least first measure the pressure in the cylinder with a compression gauge (at the same time check the spark plug). It happens that the carburetor is clogged, as well as the exhaust pipe (in the latter case, a scooter that accelerates to 60 km/h has difficulty accelerating to a maximum of 20 km/h). As for a clogged exhaust pipe, either the pipe is replaced, or the removed pipe is placed in a fire, heated, and then the soot is shaken out of it. Another method is possible (if you know a welder): a thick part of the pipe is sawed with a grinder (lengthwise), the soot is shaken out, then the pipe is welded.

Why does a scooter pick up speed poorly?

Belt variator . It happens that over time the variator belt wears out. It is enough to wear down by 1-1.5 mm. and this can reduce both acceleration speed and top speed. Moreover, the maximum speed can be reduced by 20 km/h, just 1-2 mm of a worn variator belt. Therefore, it is worth checking the width of the belt sometimes. Ideally, the belt should be replaced when worn by 1 mm. And belt wear should not be allowed to exceed 1.5 mm.
Variator rollers . If the variator rollers are worn out, this will also reduce the maximum speed. There are two reasons why the rollers can fail: – The rollers have worn out and become lighter in weight; – The shape of the roller has changed from round to triangular or quadrangular. In this case, you need to replace the variator rollers. To prevent this from happening, the rollers need to be changed on time. If you have cheap Chinese quality CVT rollers, then you need to check them every 4-5 thousand km. If you have original high-quality rollers, then you need to check them every 15-18 thousand km.
Air filter . The reason that the scooter does not pick up speed well may be a clogged air filter. In this case, the maximum power of the scooter may drop significantly due to lack of air. Moreover, fuel consumption in a scooter increases, maximum speed and acceleration dynamics decrease.
Piston . Wear of the scooter's piston can cause deterioration in dynamics and a decrease in the maximum speed of the scooter. You need to check the compression, it should be at least 7 atm.
Silencer . A clogged muffler will not allow your scooter to accelerate up to 40 km/h (for 50cc). This usually only happens on two-stroke scooters.
The reasons that the scooter does not reach maximum speed can also be: a dirty or incorrectly configured carburetor, poor quality gasoline and oil, worn bearings. There may also be such primitive reasons as heavy weight or driving against the wind. The increase in weight that the scooter carries affects the dynamics of acceleration and maximum speed.

How to clean the muffler

Manually

With a metal cable, acting like a brush. Convenient, fast, but not for long.

Heat treatment

With a blowtorch or in an oven or barbecue (but then be sure to remove the muffler from the scooter). The muffler warms up as much as possible. With blows, the soot resulting from calcination is shed off, and it is blown out using a compressor. Effective, but the result will look unaesthetic.

Chemical treatment

Dismantle the muffler. Wash with pipe cleaner or other caustic liquid, such as sodium hydroxide. Rinse with clean water. Dry well. The end result is a very high quality one. But it’s long and difficult.

What to do if the variator belt is worn out

Both longitudinal and transverse cracks require replacement of the variator. Moreover, it is better not to delay it in order to avoid serious consequences.

Muffler cleaning

It is easy to replace the variator belt if you do not delay this procedure before the belt fails. If you tighten until the weights fall apart, you will most likely need to completely replace the entire mechanism. It’s cheaper and easier not to delay.

To change the belt, all you need is a gas wrench. But it will be difficult to completely replace the mechanism without special tools.

Checking the carburetor and fuel system

Possible malfunctions:

Gasoline is contaminated, old or contains water, i.e. substandard .
The gas tap has problems with passage, with the lid, and often with the fuel filter.
The carburetor is not adjusted or cleaned.
The air filter is damaged or wet (and this happens).
Severe ruptures or cracks in gaskets or carburetor pipe.

Checking the carburetor if the scooter malfunctions

The starting enrichment is faulty or does not work

The second reason is that the starting enricher does not work. For normal starting of the scooter engine when cold and stable operation at idle before it warms up, the carburetor must prepare a slightly enriched mixture compared to normal operation. The mixture is enriched by opening an additional fuel channel using an automatic starting enricher. In fact, the role of the starter booster is often underestimated by scooter riders and this point is overlooked. If there are no problems during a hot start, but during a cold start and stable operation after starting is difficult, the carburetor is still clean and the compression is normal - be sure to look at the starting enrichment. How to check it was described in detail in this article.

Why does the scooter not reach maximum speed?

Let's imagine this situation... You bought a new 49.9 cc scooter and easily accelerate it to 60 km/h, enjoying it. But over time, you notice that you cannot accelerate it to maximum speed. Don't panic right away. The sooner you notice this, the easier and cheaper the repair will be. If the scooter's engine lacks power, do a visual check. To do this, start the scooter and add a little gas to observe. If the engine revs poorly, there may be several reasons:

clogged air filter;
the spark plug is faulty;
clogged gas filter or carburetor;
clogged muffler;
faulty starting enrichment;
clogged or leaking rubber gas and air pipes leading to the gas valve and carburetor.
transmission malfunction;
piston wear;

Let's look at the reasons and start with the simplest. After each action, it is necessary to start the engine and check it for changes in operation.

2. If this does not help, then check the spark plug. We unscrew the spark plug and check for the presence of a spark. Reasons for lack of spark:

faulty or dirty spark plug;
broken or shorted wiring;
broken or “shorted” ignition coil;
broken or “shorted” inductive ignition sensor;
faulty ignition switch;
faulty generator;

faulty or dirty spark plug;
over-enriched mixture;
inappropriate spark plug heat rating;
problems with the piston - it splashes with oil

3. The next step is to check the compression in the engine cylinder. If there is no compression or low (4-6 atm), then here are several reasons:

faulty reed valve - for 2t engines;
leakage through the crankcase, for example through the crankshaft seals - for 2t engines;
burnt or loose valves - for 4t engines;
torn cylinder head gasket;
burnt or worn piston or cylinder, or rings;
crack in the cylinder head.

If we have determined the cause, then we begin the repair. Well, if the cylinder is in complete order, then proceed to the next step.

5. The muffler may be clogged and needs to be cleaned. A clogged muffler causes a lot of problems; usually, after cleaning, the scooter becomes unrecognizable.

It happens that the scooter easily picks up maximum speed at first, but over time it picks up speed worse and worse. The maximum speed that the scooter can reach is also reduced. But it's not scary. You just need to determine the reason and return everything as it was. In this article we will talk about why a scooter does not pick up speed well.

If you have a Chinese scooter of 50 cc, then check that you really have 50 cc. Often Chinese engineers install a piston engine not of 50 cubic meters but up to 80. This does not cost more and the scooter has better dynamics and maximum speed. But it happens that a Chinese scooter has 150cc, but it cannot accelerate more than 70 km/h. Such scooters are not supplied to Europe through strict controls, but successfully enter the countries of the former USSR.

Checking compression in the cylinder

If the scooter engine does not pick up speed, but everything is in order with the carburetor, you need to check the cylinder compression.

The compression diagnostic process will help assess the condition of the cylinder-piston group without disassembling it. As a rule, damage to the piston rings occurs with reduced compression. For four-stroke engines, it may also mean that the valves are not tightly seated in the seats.

Compression is measured with a compression gauge, which can easily be replaced with an ordinary pressure gauge with a check valve. The compression gauge is mounted in place of the spark plug in the cylinder. To purchase it, you can visit any auto store, it’s inexpensive.

The condition of the cylinder-piston group will help evaluate the compression diagnostic process

Possible reasons for low compression (less than 6 atm) or its absence:

non-working reed valve - for 2 tons of engines;
leakage through the crankcase, usually through the crankshaft seals - for 2 tons of engines;
severely burnt or insufficiently tight valves - for 4 tons of engines;
damaged cylinder head gasket;
burnout or wear of the piston, cylinder or ring;
microcracks in the cylinder head.

Diagnostics and repair procedure

The scooter does not develop speed; this is generally a very popular problem among scooter owners, regardless of capacity and manufacturer. Moreover, its manifestation is quite diverse. For some people right away, for others after a run or after warming up. But there is always a reason.

There are many reasons why a scooter does not gain momentum.

So, why doesn’t the scooter gain or develop momentum?

The scooter simply doesn't have enough power. Don't be alarmed, it's just a set of mechanisms that obey the laws of mechanics, which means they can be understood and repaired. And since the scooter is a simple device, you can identify the problem yourself and fix it.

The operation of a scooter is determined by 3 components: fuel, compression and spark. Therefore, if the scooter does not gain momentum, then you must definitely check the condition of these components. And, ruling out the presence of faults sequentially, we will find the cause and eliminate it.

Checking the spark plug

The condition of the spark plug provides a lot of information for understanding the causes of the malfunction and, accordingly, for choosing repair actions.

Acceptable view

The appearance is light, slight precipitation or electrocorrosion is possible.

To understand the causes of a malfunction, the condition of the spark plug provides a lot of information.

Carbon deposits on the candle

Recommended actions:

adjustment of the working mixture;
adjust the cold start system of the scooter engine;
replace the air filter;
Cleaning the spark plug or replacing it with a new one. In this case, it is important to select the correct heat number.

Overheat

Recommended actions:

change the torque of the scooter's spark plug;
debug the scooter engine cooling system;
understand the ignition system;
understand the glow number of the spark plug (a value characterizing the spark plug, proportional to the average pressure at which glow ignition begins to appear during testing of the spark plug on a motor calibration unit).

Carbon deposits on the spark plug may cause the scooter to malfunction.

Oil contamination

Recommended actions:

change the ratio of gasoline and oil in the fuel mixture, replace the spark plugs of the scooter (for two-stroke engines);
Check the condition of the scooter engine; you may have to repair it.

In general, it is believed that if a Chinese scooter does not start well and does not gain momentum, then, unlike European and Japanese scooters, the problem is most often in the ignition system.

Why does the moped not gain momentum?

Alpha moped does not rise

What if a moped's four-stroke engine doesn't work?

Motorcycle technology is more widespread now than ever, but it doesn't take your breath away as this vehicle is very comfortable and economical. This is not surprising, but even the usual type of equipment often breaks down, and the owner does not know how to repair his two-wheeled stallion. A very common problem is inconsistency in engine operation, which occurs from time to time at one time, and in some cases after the intervention of an inexperienced owner. In any case, you can fix the breakdown without outside help, without visiting a special workshop where you need to carry out careful repairs, even if the breakdown itself is minor. As annoying as it may be, repair shop owners often jump at the chance to scale up to squeeze more revenue out of a motorcycle. Therefore, it is better to learn how to maintain your own transport without outside help, which will not only save you money, but also allow you to carry out repairs and maintenance.

Possible premises Why the moped does not rotate and does not fix

If you encounter such a problem and do not understand why the moped does not pick up, then the cause of the malfunction must be calculated. In fact, there are many circumstances where the engine cannot reach 100% speed, resulting in severe power failure, inconsistent engine performance, poor starting, increased fuel consumption and other disadvantages due to insufficient engine speed.

In most cases, the candle is to blame

Yes, yes, most often the answer to the question of why the scooter does not gain momentum and stalls is the spark plug.

As a result of using low-quality fuel, the gap between the electrodes of the spark plug is filled with carbon deposits. Because of this, spark formation deteriorates, or it cannot form at all. In some cases, too small a distance between the electrodes leads to the formation of a short circuit between them.

In order to get rid of problems, it is necessary to periodically remove carbon from the spark plugs, and also use a feeler gauge to check the size of the gap between the electrodes. For two-stroke engines, the gap is 0.6 to 0.7 mm.

Owners of motorcycles in Kyiv, who often purchase scooters through the website https://dvako.com.ua/, have learned to clean the spark plug without removing it from the cylinder, simply periodically increasing the engine speed to the maximum. You can also file down the side electrode (its end should only reach the middle of the central contact) without changing the distance between the electrodes. This approach allows the spark plug to operate more stably even when carbon deposits form. But you should not remove part of the electrode if almost no carbon deposits are formed.

Alpha moped does not gain momentum

What to do if the four-stroke engine of a moped does not gain speed?

Today, more than ever, motorcycle technology has become very common, but this is not surprising because this vehicle is very convenient and economical. Oddly enough, even such a simple type of equipment very often breaks down and the owner does not know how to repair his “two-wheeled horse.” A very common problem is instability in engine operation, which sometimes comes suddenly, and in some cases after intervention in the system by an inept owner. In any case, you can fix the breakdown yourself, without visiting a special workshop, where you would have to pay a tidy sum for repairs, even if the breakdown itself were minor. Unfortunately, repair shop owners often do not miss the opportunity to exaggerate in order to squeeze more revenue out of the motorcycle owner. Therefore, it is better to learn to maintain your vehicle yourself, which will not only save you money, but also give you repair and maintenance skills.

Possible reasons why the moped does not gain momentum and solutions

If you are faced with such a problem and do not know why the moped does not gain momentum, then you should calculate the reason causing this deficiency. In fact, there are many reasons when the engine cannot reach 100% speed, resulting in a severe loss of power, instability in engine operation, poor starting, increased fuel consumption, and other shortcomings that appear as a result of missing engine speed are also possible.

The motor of a moped is an important element that greatly affects the quality of the ride, so you should always pay due attention to this unit, even in the event of minor breakdowns. Timely maintenance and elimination of emerging deficiencies allows you to eliminate future breakdowns, extend the service life of the moped and extend its technical condition. But still, if it would seem that the technical condition is normal, but the moped does not gain momentum, what to do in this case.

First, you need to determine which node is failing. To do this, you need to take a toolbox and first unscrew the spark plug. A very common cause of this problem is a damaged spark plug. After unscrewing, visually it will be quite normal, but it is worth examining it in more detail and checking its performance. The first thing you should pay attention to is the place where the spark occurs, which should be dry and light, black soot and the absence of a gap indicate poor performance of the spark plug. As a rule, the spark plug is replaced immediately.

If, after replacing the spark plug, engine operation returned to normal, but after a while the same problems with the set of revolutions arose again, then it’s worth getting into the carburetor. If the carburetor has already been previously adjusted for some reason, then it is necessary to reconfigure it in accordance with the parameters specified by the manufacturer. When you disassemble the carburetor, it is worth inspecting some of the jets and, if possible, blowing or cleaning the holes through which the fuel passes. If there is debris in the carburetor, it is necessary to completely flush the fuel system, replace the fuel filter and use sealant when reassembling the carburetor.

If the spark plug and fuel system are in excellent condition, but the delta moped does not gain momentum, what should you do under such circumstances? In this case, it is necessary to check the quality and stability of the spark supply. Very often there are cases when a spark arrives, but when the speed increases or the components heat up, its quality deteriorates, then it is necessary to clean the contacts suitable for the power nodes and, if possible, replace the elements responsible for supplying the spark.

A fairly common reason when a moped does not pick up speed under load is the gas distribution mechanism, or rather the valve. The first sign that the gas distribution mechanism is the culprit of the problem is an extraneous sound that comes from the top of the cylinder, where the gas distribution unit itself is located. This system simply cannot fail and, as a rule, repair and restoration of this part is expensive. The main reasons are a breakdown in the air filter, or insufficient air purification, which could cause a breakdown.

Heating of the engine and a very hot knee also indicate problems with the valves. In most cases, it is possible to repair this unit yourself, but most motorcycle owners do not bother, but buy a new filter and, of course, the gas distribution unit itself. Replacement is carried out by removing and installing a new cylinder head, followed by adjusting the valves and adjusting the clearances.

Other reasons why the moped stopped moving:

The air filter is clogged, if you have driven more than 2000 km, then cleaning the air filter should help. Check the valves, if they are underpressed or pinched, so as soon as you start adding gas, the moped will lose speed. If the moped has lost power after running in. This means that you need to reconfigure the carburetor, because during break-in all parts are ground in, the compression ratio in the engine may increase and the engine will operate differently. The throttle cable may also stretch; if you realize that there is no click when unscrewing sharply, then you need to tighten the cable or replace it. If you are riding a moped, you give more gas, the revolutions begin to rise, the engine howls, but the moped itself does not move.

Then on a moped the clutch slips. Another common problem why a moped starts to stall is overheating. Another reason why the moped does not pull is that the valves begin to leak or the rings allow oil into the combustion chamber, then the moped will also begin to lose power. Be sure to pay attention to the condition of the chain and sprockets, if they are worn too much - this gives additional load during rotation, so the loss of power may depend on what is heating the chain. Also check the brakes to see if they are jammed, place the moped on the center stand and spin the wheel by hand; if it spins smoothly, then the brakes are fine. And keep an eye on your tire pressure

So if your moped has lost power and stopped pulling, then take it and check everything in every detail.

Operating rules

Any manufacturer includes an instruction manual for their product. It describes when and how the scooter is serviced, how its correct operation is checked (ignition, gear shifting, engine compression and exhaust systems). If the scooter does not pick up speed, then this is primarily due to violation of these instructions. That is, you need to regularly change spark plugs, belts, oil, air filter, and monitor the quality of gasoline and oil. It is necessary to clean the contacts of the electrical system and change the battery on time. Maintenance is not only wiping the scooter from dust, but an in-depth diagnosis of all its components and mechanisms.

How to check the spark

Place the spark plug on the metal body of the engine and turn the starter.
We replace the faulty spark plug.
It is possible that the spark plug is working properly, but the spark is not produced. We check the wiring and find a break or faulty element.

Possible reasons for lack of spark:

spark plug contamination or malfunction;
wiring is broken or of poor quality;
a broken or simply high-quality coil in the ignition system;
the induction ignition sensor is broken or “shorted”;
the ignition switch is faulty;
generator is faulty.

Inspection procedure and repair methods

If the scooter does not travel more than 40 km. h., then there is a certain procedure for checking and searching for causes. Accordingly, for each reason there is its own algorithm for repair work.

There is a specific algorithm for repair work for each breakdown.

First of all, the spark plug is checked. To do this, you need to unscrew it and inspect it. If the contacts are clean, then everything is in order. If they are covered with black soot or, on the contrary, they are clean but have a red tint, then there is a problem with the mixture. Repair in this case consists of cleaning and servicing the carburetor.

Next, you can check the quality of the spark on the spark plug and, if it is weak, you need to check the contacts on the high-voltage coil, on the inductive ignition sensor and on the ignition switch. The presence of a short circuit in the specified components and breakdowns to the housing are also checked.

The next step is checking the engine. To start with its temperature. If it overheats, it could mean the mixture is too lean or the fuel is bad. This can be eliminated by cleaning the carburetor.

Sequence of repair actions

The main rule for detecting malfunctions and repairing a scooter is to step-by-step eliminate the elements of the system when identifying the causes of a breakdown in any of them. Search and repair, especially when starting from the starter, must be done in accordance with a strict sequence, where the chain may act as the beginning, and the end, for example, if there is or is no spark. It is worth noting that you do not need to immediately run for a new switch for the scooter, first make sure that the generator is functioning perfectly, only after that test the wiring if there is no spark, etc.

BRAKING

There are four types of braking: full - until the scooter stops, working - to slightly reduce the speed, parking - to hold on a slope, and emergency.

If you sharply, strongly press the brake lever, the wheel may lock - it will stop rotating and the wheel will “skid”. Locking the front wheel is dangerous - a fall is almost guaranteed. If the locking occurs at low speed, the rear wheel is likely to lift (the “stoppie” effect) and the scooter may roll over. The “skidding” of the rear wheel when moving in a straight line is not so critical, at least until the wheel begins to move to the side (in such cases they say: the wheel has skidded). If you don’t have time to release the brake in time, you will fall onto the asphalt.

On scooters with a CVT they brake in three ways: only front, only one rear, and simultaneously front and rear. Which one should you start working on earlier and which one should you press harder? It is advisable to brake simultaneously with both or with a slight advance with the rear brake.

Many beginners are prejudiced against using the front brake - they are afraid of turning over or falling. And they are mistaken: when braking, the weight falling on the front and rear wheels is redistributed, but the front one accounts for most of it. Based on this, it follows that the efficiency of one front brake is approximately 30% higher than that of only the rear. To avoid rolling over, avoid pressing the brake lever suddenly. And braking with one rear wheel is justified only on slippery surfaces.

Some people think that the rear brake is not needed at all. And this is a misconception, and a dangerous one at that. When braking with one front brake in a turn and with poor tire adhesion to the road (for example, when there is a little sand on the asphalt), the wheel drifting to the side and subsequent fall is inevitable. Therefore, do not get used to working only with the front one.

Using both brakes at the same time reduces stopping distance by 20%. When braking from a speed of 30 km/h, modern scooters stop after an average of 5–7 m.

Don't forget that you can't slow down the engine on a scooter. This means that on descents you will have to use the brakes constantly. When driving around the city, this feature does not cause any difficulties, but on long, steep descents it’s a different matter. This means that as a result of constant long-term operation, the brakes may overheat.

CONTROL ON THE ROAD

It’s one thing to master the skills of driving a scooter in an empty lot, and quite another to join the hustle and bustle of city streets. Need I remind you that while driving, all your attention should be focused on what is happening around you? If all you are doing is trying to control how you maintain your balance, including when turning, then it’s too early to hit the road.

Riders of 50cc scooters have few legal options for positioning on the roadway. They are instructed to drive in the far right lane, as close to the sidewalk or curb as possible. In life it’s different: you have to drive closer to the middle in order, say, to go around potholes or foreign objects... Blindly following traffic regulations and driving at the very edge is dangerous. What if a pedestrian takes a step off the sidewalk? Or will a careless car owner open the door of his car?.. It’s safe to stay in the middle of the right lane or even a little to the left.

You should not trail along in the same lane with a slowly moving truck or bus. And it’s better not to approach them: it gets boring quickly. In addition, it is so easy to miss an open hatch or brick that your “leader” missed between the wheels.

The difficulty of driving through city intersections is not even heavy traffic, in which it is difficult to maneuver. Multi-level interchanges in modern cities, tricky lane layouts, prohibitory traffic light signs - all this baffles even an experienced driver. Learn by heart difficult sections of the route on frequently repeated routes, master the algorithms for driving through intersections and junctions.

Law-abiding scooter riders are required to remember the restrictions prescribed for them (the main one is the prohibition of left turns on a multi-lane street). Let's hope that the outdated rules will be rewritten to take into account the increased capabilities of scooters, but until then, let accumulated experience and common sense become guides and good advisers when riding.

Why does the scooter not develop speed?

1 answer
Reply Mar 25, 2014 from Mart1z Guru (93,410 points)
The main circumstances that entail a decrease in high speed, and from time to time dynamics:
1) The variator belt has worn out by more than 1-1.5 mm, after which it is not able to reach a large radius of the variator, and therefore there is no possibility of talking about a high speed.

Troits at high rpm

Everything related to scooter repair. BE SURE to indicate the model, unit and symptoms of the malfunction in the title of the topic.

Moderators: MikeLoDeon, -JODA-, Lion
Forum Rules MUST indicate the model, unit and symptoms of the malfunction in the topic title.
Header form: [SCOOTER MODEL] – unit malfunction

Example: [Dio] electric starter does not work.

If the topic concerns general repair issues, the model may not be specified.

The main rule is that the title of the topic should be brief, but as fully as possible reflect its content. Topics whose title does not make it clear at least the approximate essence of the question, such as “AAA!!! Save!”, “I have a problem, tell me,” will be DELETED.

Troits at high rpm

janich » 15 Sep 2007 02:49
it was at stage 6, it doesn’t develop a maximum speed, and it’s very difficult to start a cold one (the spark plug looks like it’s overflowing, but there’s a spark). playing with the jets didn’t lead to anything. I swapped 21 to 17.5 + again a game with jacklers. result -0. in a dark room I noticed that the cap on the spark plug was shooting through - replacement. In general, I replaced the valve + cap + spark plug + a new piston hebo. The trouble remained. That is, the average speed is ok, higher - it immediately triples. Benz enters the carber (in There are no gaps in the filter). I accidentally noticed that if you reduce the gap on the spark plug, it becomes better, but the pain does not go away. In my opinion, the ignition current remains, the feeling that at high speeds there is not enough current. But what exactly is moping?? commutator or rotor/stator?? Does anyone have any thoughts??... I'm already tired...

janich Posts: 11 Registered: Sep 15, 2007 02:33

by cer-berus » Sep 15, 2007 03:19 AM

Usually when you change all the gaskets and seals, then you are very surprised that the scooter starts up when cold from the first push!

cer-berus Messages: 12 Registered: Sep 14, 2007 11:46 pm

Troits at high rpm

janich » Sep 15, 2007 5:28 pm

janich wrote: it was at stage 6, it doesn’t develop a maximum speed, and it’s very difficult to start a cold one (the spark plug looks like it’s overflowing, but there’s a spark). playing with the jets didn’t lead to anything. I swapped 21 to 17.5 + again the game with jets. result -0. in a dark room I noticed that the cap on the spark plug was shooting through - replacement. In general, I replaced the valve + cap + spark plug + a new piston hebo. The trouble remained. That is, the average speed is ok, higher - it immediately triples. Benz enters the carber (in There are no gaps in the filter). I accidentally noticed that if you reduce the gap on the spark plug, it becomes better, but the pain does not go away. In my opinion, the ignition current remains, the feeling that at high speeds there is not enough current. But what exactly is moping?? commutator or rotor/stator?? Does anyone have any thoughts??... I'm already tired...

janich Posts: 11 Registered: Sep 15, 2007 02:33

Fasterpast » Sep 15, 2007 5:50 pm

Reed valve?

The brakes were invented by a coward! ...But the coward was invented by the brakes! I drive: Suzuki Address V50, V100 and SkyWave Type-S 400, 650

Fasterpast Messages: 6371 Registered: Dec 22, 2000 02:00 From: Moscow What it rides on: Powered by Franco-Morini (R)

Old Man » Sep 15, 2007 09:18 pm

play with the air filter...

Women pay in kind!

Old Man Messages: 1023 Registered: May 27, 2005 07:20 pm

janich » Sep 15, 2007 11:59 pm

Fasterpast wrote: Reed valve?

visually everything fits perfectly (stock with carbon fiber), I’ll try to bend it, there’s another one.

The question on the other hand is whether such nonsense could be caused by the switch??? or “it either works or doesn’t work.”

I don't like

1-spark, when the spark plug is removed, you can see that it runs along the electrode, that is, it does not always hit one point (as if the current strength is changing)

and about the filter - what is there to play with?? the same thing is done with jets, the current is adjusted to the incoming air, or am I wrong??

janich Posts: 11 Registered: Sep 15, 2007 02:33

Fasterpast » Sep 16, 2007 00:43

What filter do you have? Federal Tax Service?

The brakes were invented by a coward! ...But the coward was invented by the brakes! I drive: Suzuki Address V50, V100 and SkyWave Type-S 400, 650

Fasterpast Messages: 6371 Registered: Dec 22, 2000 02:00 From: Moscow What it rides on: Powered by Franco-Morini (R)

janich » Sep 16, 2007 01:09 AM

red sponge

janich Posts: 11 Registered: Sep 15, 2007 02:33

by janich » Sep 16, 2007 01:10 am

so the thing is that before, in the same configuration as he is moping now, he then

janich Posts: 11 Registered: Sep 15, 2007 02:33

by janich » Sep 16, 2007 6:34 pm

plugged the valve into another container - don’t care

janich Posts: 11 Registered: Sep 15, 2007 02:33

CrashEr » Sep 16, 2007 7:04 pm

Did you change the spark plug? If so, are you sure they are not fake? What is the heat number? What pipe? Are there any foreign objects in the pipe or in the exhaust in general? Is there a dent in the pipe near the cylinder? Is the enrichment in the carburetor working? You can try to completely drown out his channel. Did you wash the carburetor CAREFULLY and EVERYWHERE (that is, generally everywhere possible)? It would be nice to borrow a working switch from someone to check.

A fully equipped Duke costs the same as two Dreadnoughts, with Dukes being more fearsome and lasting longer. (c) David Lloyd George

CrashEr Messages: 1554 Registered: May 28, 2005 18:53 From: Moscow

janich » Sep 17, 2007 00:52

I changed the spark plug, there were two working spark plugs (both glowed at number eight), one had a long thread and the other had a short thread, both worked (I went to buy a long one on the short one)

ES if I'm not mistaken). pipe C16, cylinder new zero, and the old one is also moping. We tried both carburetors, 17 and 21 (read higher). But with a favor it’s difficult, even very difficult, so I’m asking you

Could it be because of HIM that such nonsense can happen - there is a spark, but not in time / not stable / weak

janich Posts: 11 Registered: Sep 15, 2007 02:33

janich » Sep 19, 2007 10:21 am

janich wrote: I
changed the spark plug, there were two working spark plugs (both glowed at number eight), one had a long thread, the other was short, both worked (I was going to buy a long one on the short one)
ES if I'm not mistaken). pipe C16, cylinder new zero, and the old one is also moping. We tried both carburetors, 17 and 21 (read higher). But with a favor it’s difficult, even very difficult, so I’m asking you
Could it be because of HIM that such nonsense can happen - there is a spark, but not in time / not stable / weak

janich Posts: 11 Registered: Sep 15, 2007 02:33

reldev » Sep 22, 2007 4:31 pm

I had a similar experience. I decided to completely disassemble it and noticed that the ground bolt was unscrewed almost all the way! Well, this may not apply to your case if you didn’t unscrew the mass...

reldev Posts: 531 Joined: Jun 26, 2006 3:41 pm

Website
ICQ

sick guy » Sep 22, 2007 4:46 pm

I have the same problem, after 50 km/h it starts to trip, they told me that it’s my switch that is strangled. I have dio 34. Is this true? tell.

sick guy Messages: 51 Registered: Aug 22, 2007 3:49 pm

Return to Repair

Who's at the conference now?

Currently browsing this forum: no registered users

Possible reasons

First of all, you need to look for a breakdown in the scooter’s structure, but you also shouldn’t forget about other reasons, for example, external influences. The main breakdowns will be discussed below.

Belt variator

A variator is a device for increasing the speed of a scooter by using rollers of different diameters. The main element of this mechanism is a belt that transmits torque. It must be of a certain length, width and, most importantly, thickness. A slight wear of the belt by just 1 mm can change the overall radius of the belt loop, which leads to a drop in the maximum speed. It is clear that you cannot measure the thickness of the belt by eye; for this you will need a caliper. If the measurement shows a deviation from the norm by 1 or 1.5 mm, the belt should be replaced

There are several types of scooter breakdowns

CVT rollers

These elements of the gear shifting mechanism wear out over time. They become thinner or lose their correct geometry, for example, only one side of the roller wears off and it stops performing its functions. The repair is simple - replacing the worn out roller. There are two options for rollers - expensive high-quality and cheap. Knowledgeable people recommend buying cheap ones, since both of them are erased after about 3-5 thousand kilometers. Therefore, there is no point in overpaying.

Air filter

A visual inspection of the spark plug helps to understand that the reason is in this particular unit - it is covered with black deposits. It is also worth paying attention to increased fuel consumption, this also indicates a problem with the air filter. That is, the combustible mixture becomes enriched due to lack of air, hence the deposit on the spark plug and increased gasoline consumption.

Several parts in this unit may become unusable - sealing rings on the cylinder, cylinder walls, for example, due to scratches, chips on the piston. Piston problems are easily diagnosed by measuring compression. If it is less than 7 atmospheres, then you need to disassemble the engine. Repair depends on the degree of destruction of the piston, but in any case, it is necessary to replace all gaskets in the block, even if the repair consisted of replacing the O-ring.

The variator belt must be of a certain length

If it is clogged, then the engine power is sharply reduced. Repair consists of replacing the muffler or burning it. It is possible, in principle, to remove it completely, but then the roar of the engine will disturb the peace of the townspeople.

Dirty carburetor

This device is designed to prepare a combustible mixture consisting of gasoline and air, which are mixed in certain proportions. A carburetor is a rather complex device, having a lot of nozzles and jets. This is precisely how they can become clogged during operation with dust or small fractions floating in gasoline. The holes are so small that to clean it you will have to completely disassemble the carburetor and blow them out with a compressor, and the device itself must be thoroughly wiped with gasoline, both inside and out. If you don’t have a compressor at hand, you can try to clean the inside of the carburetor with a special compound, sold in auto stores in the form of aerosol cans.

Scooter carburetor clogged

Another important point is that the jets and channels of the scooter’s carburetor are clogged. In this case, as stated in many articles, normal starting and stable idle operation are unlikely. Of course, in this case, you need to remove the carburetor and blow out the jets and channels with a special liquid. The jets must first be unscrewed. Don't forget also about the channels of the starting enrichment. We looked at how to properly clean a scooter carburetor here.

In the Liqui Moly product line there is such a product - Motorbike Luft-Filter-Oil. This is an ultra-sticky liquid synthetic composition for impregnation of reusable porous filter materials. It is necessary in order to improve the collection of dust and sand. That is, the principle of operation is almost the same as that of a fly catching tape. Despite its super stickiness, Motorbike Luft-Filter-Oil does not impair the passage of air through the foam rubber, but prevents the penetration of abrasive and water through the filter. The composition is optimal not only for servicing standard and tuned air filters of scooters, but can also be used for cross-country motorcycles.

The life of the engine hangs by a thread

We sorted out the filter. Now let's move directly to scooter engines, which come in two types: 2-stroke and 4-stroke. The Achilles heel of “two-stroke” engines is the oil pump, which pumps oil from a special tank in small doses into the carburetor, where it is mixed with gasoline, after which the mixture enters the combustion chamber. The oil pump is driven by a cable directly connected to the throttle handle (the more you unscrew the handle, the greater the performance of the oil pump).

FAQ: Why does the cold one move, but the hot one stalls?

Everyone wants their equipment to ride well and do it in any conditions, but many people paid attention to the fact that when it’s cold, the moped rides much better than when it warms up. I, just like many now, was puzzled over this question and understanding of its essence did not come immediately...

Physics.8th grade

Everyone studied in the eighth grade, at least those who were interested in the pressing issue. All bodies and gases expand when heated, and the lower their initial temperature, the greater their expansion coefficient will be when heated to a certain temperature relative to the initial one.

Intercooler or nitrous oxide injection

Almost everyone knows about nitrous oxide, everyone has watched super-sophisticated children's films like “The Fast and the Furious” (by the way, the real name of the movie is “Fast and Fierce”, but marketers don’t give a damn about the correctness of the translation. Author’s note), fewer people know about the intercooler, but about the principle of operation Few people even know both systems. So what am I talking about?

Almost the essence

Everyone thinks that nitrous oxide is something really fucking flammable and when it burns it releases an equally crazy amount of heat and energy. Anyone who thinks that way, go back to school, only this time to chemistry class. Bullshit! Nitrous oxide creates an environment for combustion, or rather, it just cools the fuel-air mixture to fairly low temperatures and, in addition, by disintegrating at high temperatures, it releases an additional portion of oxygen.

An intercooler does almost the same thing: it’s a kind of refrigerator that simply greatly cools the atmospheric air before it enters the combustion chamber. That’s all.

Have you noticed that in cold weather the moped really stalls, but in the heat it drives rather mediocre?

The essence

So, what exactly is the whole point? It is that while the engine is cold, firstly, an additional portion of gasoline is supplied to it for a cold start, and secondly, IT IS COLD, and the air does not heat up against a cold engine.

Ask: well, why doesn’t a hot engine drive so well? It doesn’t drive because even before the fuel-air mixture ignites, it manages to heat up in the engine itself and pre-expand to some extent, which is completely unnecessary and out of place, well and plus to everything, the enrichment channel has already closed, which no longer provides additional. portion of gasoline and air.

I had one fuckmobile for repairs: Suzuki Address V, and so it didn’t want to start at all, and after various attempts to correct the situation, I took it and simply unscrewed it and threw out the jet on the enrichment channel. I never thought that the moped, however It’s more of a crappy Suzuka, maybe it can drive like that. It’s true that she ate accordingly...

pitstopsaki.com

loss of speed when driving

#1 OFFLINE serg83

User
7 messages
0 I'll go
Name: Sergey
Yoshkar-ola city
Wheels: nexus x1

Post edited by serg83: 28 March 2012 – 02:21 PM

#2 OFFLINE Nahlebnik

User 2502 posts 2 I'll go

Name: Alexander
Moscow city
Wheels: Suzuki Intruder VL1500 LC

Post edited by Nahlebnik: 28 March 2012 – 02:40 PM

#3 OFFLINE Topotun

SIM drive

1939 messages 0 I'll go

Tel.: +7 9I5 O2H O7 7Z
Name: -
Moscow city
Wheels: SYM O'eklmn (was). Honda Shadow Aero

nexus x1 equipment? look at the vacuum tube going from the carburetor to the fuel pump - if there is even a smell of gasoline in it, change the fuel pump. Another question: is everything okay with the membrane in the carb? Is the damper not sticking?

In general, according to the symptoms, the problem may not be in the supply of gasoline or air, but in the electrics (coil, switch)

Post edited by Topotun: 28 March 2012 – 04:20 PM

SYM CLUB

3167 messages 0 I'll go

Name: Oleg
Moscow city
Wheels: Honda CN 250, SsangYong Korando 2.3 TD

#5 OFFLINE BadCat

Organizer

8178 messages 6 I'll go

Tel.: +7 9Ib Zb9 9I Z8
Name: Dmitry (Cat)
Lyubertsy city
Wheels: VFR1200X Crosstourer

There is no need to drive faster than your guardian angel flies.

#6 OFFLINE serg83

User 7 messages 0 I'll go

Name: Sergey
Yoshkar-ola city
Wheels: nexus x1

Can you give more details? It is very difficult to assess the color of soot from such a description. The normal color of soot on a spark plug is described as “The center electrode skirt is light brown in color with minimal soot and deposits.” Well, not chocolate at all. Maybe the mixture is too rich?

Why does the idle speed float?

Engine idle control is broken

Most likely, due to some factors, the regulation was carried out towards a leaner fuel mixture at idle. Adjust the idle speed using the “quantity” and “quality” screws of the fuel mixture.

The channels and/or jets of the carburetor idle system are clogged

The fuel mixture becomes lean. Remove the idle air system fuel nozzle. Clean it, wash it with fuel, blow it with compressed air. If it is deformed or its markings do not match the required ones, replace it.

Foreign air leaking into the carburetor

In this case, the fuel mixture is depleted of excess air. The engine is tripping.

Low or, on the contrary, very high degree of fuel in the carburetor float chamber

The fuel mixture again becomes leaner or, on the contrary, becomes very rich, flooding the spark plug. It is necessary to check and adjust the fuel level in the carburetor float chamber. In addition, you should pay attention to the integrity and position of the floats, and also check the needle-shaped valve, since the size of the fuel level in the float chamber and the subsequent mixture formation directly depend on them.

Scooter air filter clogged

The degree of contamination of the air filter should be quite high, for example, as in the photo. Change the filter element.