Motorcycle engines: design, principle of operation, technical characteristics

Types of motorcycle engines

There are two-stroke and four-stroke engines, the operating principles of which are somewhat different.

Also, motorcycles have different numbers of cylinders.

In addition to the original carburetor engine, you can often find injection units. And if motorcyclists are accustomed to fixing the first type on their own, then it is already problematic to repair an injection engine with a direct injection system with your own hands. Diesel motorcycles and even those with an electric motor have been produced for a long time. The article will discuss the characteristics of a carburetor-type motorcycle engine.

Cylinder volume: what formula to use

To solve this problem, a convenient tool can be useful - an online calculator. If you are interested in the question of how to find out the working volume of a cylinder in your own passenger car , you will need some of its characteristics, namely height and radius divided by diameter.

You can independently calculate the volume of a cylinder using the formula:

If the diameter is known, then the formula will help calculate the volume of the cylinder:

Instead of the radius, the diameter value is indicated. Having the necessary characteristics, computing operations will not seem like a complicated process.

Car engine power calculator

Online converter of volume, units and measurement systems, conversion of volume values

Pit calculation calculator, cost of excavation work, calculation of pit volume of different shapes

Injector performance calculator

Tire load index calculator

Calculator for empirical calculation of oil change intervals based on actual fuel consumption

Source

Four stroke engine

Such engines have a duty cycle of four piston strokes and two crankshaft revolutions. The engine diagram clearly shows the structure of a piston internal combustion engine and its working process.

1. On intake, the piston moves down from top dead center, drawing mixture through the open valve.
2. During compression, the piston rising from bottom dead center compresses the mixture.
3. During the working stroke, the mixture, ignited by an electric spark plug, burns, and the gases move the piston down.
4. When exhausting, the piston, rising, pushes the exhaust gases through the open exhaust valve. When it reaches top dead center again, the exhaust valve closes and the whole process repeats.

The advantages of four strokes are:

• reliability;
• efficiency;
• less harmful exhaust;
• little noise;
• Oil and gasoline are not pre-mixed.

The design of this type can be depicted by the following engine diagram.

Sportbike

We say “sportbike” - we mean “power-to-power”, the motto of the designs is maximum power with minimum weight. The rest is on the side. Why worry about drag at the bottom if the sportbike engine “loves to live” in the mode when the needle is at the red line of the tachometer. This is a high-end technical thought of the motorcycle industry, they contain all the latest developments. The best maneuverability, acceleration dynamics and braking efficiency - all these are sportbikes - conveyor versions of the famous two-wheeled Grand Prix cars.

Two stroke engine

The engine capacity of this type of motorcycle is usually smaller, and the working cycle takes one revolution. In addition, it does not have intake or exhaust valves. This work is performed by the piston itself, which opens and closes the channels and windows on the cylindrical mirror. A crankcase is also used for gas exchange.

The advantages of this engine are:

• with the same cylinder volume, it has a power that is 1.5-1.8 times greater than a four-stroke;
• does not have a camshaft and valve system;
• production is cheaper.

Method for determining engine displacement

To solve this problem, you will need to find out the volume of one cylinder, multiply the resulting number by the number of cylinders in the internal combustion engine . For a rough understanding, the calculation formula is given below:

V engine = Pi * radius squared * stroke height * number of cylinders.

Volume is measured in cubic centimeters, while characteristics are measured in millimeters. If you need to convert between units, simply divide the resulting number by 1000.

Please pay attention! The full and working dimensions of the engine differ in values, which is due to the recesses of the pistons and bulges.

How to find out the volume of a cylinder? To do this, you need to add the values ​​of the working value and the camera size. You can find out the real indicator of the power unit using a calculator. To do this, you need to know the parameters in cm³ , piston and cylinder.

Why do you need to check the characteristics of the internal combustion engine?

The desire to know this value is most often motivated by the desire to increase the compression ratio. This procedure is often of interest to car tuning enthusiasts. Boring the cylinders allows you to increase the compression ratio and pressure on the piston.

The power unit produces more horsepower with the same amount of fuel mixture consumed. However, in an effort to achieve maximum efficiency, the motor often cannot withstand the load and fails after a deafening explosion.

How to find out the main parameter of a unit using the VIN code

VIN is an identification number assigned to each vehicle. This is a set of unique letters and numbers that help you find out the characteristics of the motor. You only need to look at the vehicle’s registration certificate before finding out the desired value. For example, for a standard four-cylinder installation:

1. In this formula, D serves to determine the motor diameter (in mm),
2. H is used to indicate the stroke of the piston.

In order to indicate engine volume in documentation, cubic centimeters are often used. The indicator is also indicated in liters .

Cylinders and the work process in them

The working process of one and the other engine occurs in the cylinder.

The piston here moves along a cylindrical mirror or insert sleeve. If air cooling is used, then the cylindrical jackets have ribs, and with water cooling they have internal cavities.

The crankshaft, through the connecting rod, perceives the movement of the piston, transforming it into rotation, and then transmitting torque to the transmission. It also powers the gas distribution mechanism, pump, generator and balance shafts. The crankshaft has one or more elbows depending on the number of cylinders.

In a four-stroke engine, in order to better fill the cylinder with the mixture, the intake begins before the piston reaches top dead center, and ends after it passes bottom dead center.

Its cleaning begins even before reaching bottom dead center, and exhaust gases are pushed out as the piston moves to top dead center. The exhaust valve then closes to allow the gases to leave the cylinder.

The following types of gas distribution mechanism are used on this type of engine:

• OHV;
• OHC;
• DOHC.

The latter type has a minimal number of elements, so the crankshaft can rotate faster. Therefore, DOHC is becoming increasingly common.

Four-stroke engines have a more complex design compared to two-stroke engines, as they have a lubrication system and a gas distribution mechanism that two-stroke engines do not have. However, they have become widespread due to their cost-effectiveness and less harmful impact on the environment.

Motorcycle engines are most often one-, two-, and four-cylinder. But there are also units with three, six and ten cylinders. The cylinders are in-line - longitudinal or transverse, horizontally opposed, V-shaped and L-shaped. These motorcycles usually have an engine displacement of no more than one and a half thousand cubic meters. Engine power is from one hundred fifty to one hundred eighty horsepower.

Motorcycle engines

As you know, internal combustion engines (ICE) are of three types, namely two-stroke, four-stroke and rotary.
The latter are not very common, but some motorcycle manufacturers still use them (Triumf). General structure and operation of the engine

Motorcycles are equipped with internal combustion engines (ICE), in the cylinders of which the thermal energy of burning fuel is converted into mechanical work. The reciprocating motion of the piston, which receives gas pressure, is converted into rotation of the crankshaft through a crank mechanism, which consists of a cylinder, a piston with rings, a piston pin, a connecting rod and a crankshaft. The extreme positions of the piston moving in the cylinder are called dead centers - top dead center (TDC) and bottom dead center (BDC). The distance from TDC to BDC is called the piston stroke, and the space created is called the cylinder displacement (cm3). The total internal volume of the cylinder consists of the working volume and the volume of the combustion chamber. The ratio of the total volume to the volume of the combustion chamber is called the compression ratio; the higher it is, the more efficient the engine's operating process is. Modern engines have a compression ratio of 9–10 units (higher values ​​are found in sports models).

Piston internal combustion engine

For two- and four-stroke internal combustion engines, the workflow and design of parts are somewhat different.

Four-stroke engines

In four-stroke engines, the working cycle occurs in four piston strokes (stroke) and two revolutions of the crankshaft: intake - the piston descends from TDC and sucks in the combustible mixture through the open intake valve; compression - the piston rising from BDC compresses the working mixture with the valves closed; working stroke - the mixture burns, ignited by an electric spark, and the resulting gases, expanding, move the piston down (this stroke of the piston is called the working stroke, since during it useful work is done); exhaust - the upward moving piston pushes the exhaust gases through the open exhaust valve.

Working process of four stroke engine

Two-stroke engines

In two-stroke engines, one power cycle occurs per revolution of the crankshaft. Another feature is the absence of valves (intake and exhaust) with a mechanical drive. Their role is played by the piston itself, opening and closing special windows and channels on the cylinder mirror, and on some engines a reed valve is installed at the inlet. The crankcase volume under the piston is also used for gas exchange.

Working process of two-stroke engine

When the piston moves upward from BDC, the working mixture is injected into the sub-piston space, and in the space above the piston, the exhaust gases remaining from the previous cycle are first displaced, and later, when the windows are closed by the edge of the piston, compression occurs. At TDC, the mixture in the combustion chamber is ignited by an electric spark formed between the electrodes of the spark plug. The burning fuel-air mixture expands and pushes the piston down - a working stroke occurs. Having dropped approximately 2/3 of its stroke, the upper edge of the piston opens the windows in the cylinder. Exhaust gases under excess pressure exit through the exhaust window into the exhaust pipe. Through other windows, fresh charge enters the cylinder from the crankcase cavity, where the descending piston creates excess pressure. This flow of mixture is called purging, and windows and channels are called purging.

Modern two-stroke internal combustion engines have multi-channel (3–7 channels) return-loop purge. In addition, a check plate (petal) valve is installed at the inlet of the cylinder, which is controlled by the vacuum in the crankcase. During inlet into the crankcase (the piston moves from BDC to TDC), under the influence of vacuum in the sub-piston space, the valve plates open the passage of the combustible mixture from the carburetor. When the piston moves back (during purging), excess pressure in the crankcase closes the valve plates, preventing the mixture from being thrown back from the crankcase into the carburetor. The reed valve improves cylinder filling, increases engine power and efficiency, especially at low and medium crankshaft speeds. Many engines also have a special mechanism that changes the height of the exhaust port (and therefore the duration of exhaust) depending on the engine speed (the so-called “controlled exhaust”). Despite the measures taken to improve the gas exchange of two-stroke internal combustion engines, some of the mixture leaves with the exhaust gases, which reduces their efficiency compared to four-stroke engines.

The working process of both two- and four-stroke internal combustion engines occurs in the cylinder. The piston moves along the inner surface (mirror) of the cylinder or insert liner. In modern engines, instead of steel or cast iron liners, carbide nickel-silicon compositions (“Nikasil”) are used, sprayed directly onto the aluminum cylinder base. Depending on the type of cooling system adopted, the cylinder jackets have fins (air cooling) or internal cavities for the passage of coolant.

The piston perceives gas pressure during combustion of the working mixture. It consists of the upper and lower parts (head and skirt, respectively) and the piston pin mounting bosses. The shape of the bottom can be flat or convex; four-stroke engines often have recesses in the bottom for valves. In the piston skirt of two-stroke engines there are cutouts through which the combustible mixture passes, because in these engines the piston controls the gas distribution (intake, scavenging and exhaust).

Pistons of two-stroke (a) and four-stroke engines (b)

1 - piston head; 2 — selections for valves; 3 — compression rings; 4 — oil scraper ring; 5 — piston pin mounting bosses; 6 — piston skirt; 7 — cutout for the purge window; 8 — oil trap cavity (refrigerator); 9 — cutout for an additional purge window

The piston head has thickened walls that house 1–3 compression rings made of special cast iron or steel. These rings seal the gap between the piston and the cylinder mirror and remove heat into the cylinder walls. In four-stroke engines, in addition to compression rings, the piston has an oil scraper ring that removes excess oil from the cylinder bore.

The bosses serve as a support for the piston pin, they have grooves for the retaining ring and holes for oil mist lubrication. Often in the area of ​​the bosses, on the outer surface of the piston, special recesses are made - refrigerators.

The skirt directs the movement of the piston. Due to the unequal thermal expansion of different parts of the piston, its outer surface is given a complex shape: barrel-shaped (conical) in height and oval in circumference. Pistons are made from high-quality aluminum alloys with a high silicon content, which can withstand high thermal and mechanical loads, and at the same time have a low expansion coefficient.

The piston pin pivotally connects the piston to the connecting rod. Typically, a floating pin fit is used in the piston bosses and the upper head of the connecting rod; it is secured from axial movements by spring retaining rings in the bosses.

The connecting rod transmits force from the piston to the crankshaft and consists of a rod (I-beam or elliptical section) and heads: upper and lower. Depending on the type of engine and the lubrication system used, the connecting rod heads are made with plain bearings (with bushings or liners) or rolling bearings (roller, needle). When a plain bearing (liner) is used in the lower head, the head itself is detachable. In the case of using a needle bearing, the head is made one-piece and the lower journal of the shaft is pressed into the cheeks.

Connecting rods

a - with a detachable lower head (“Dnepr”); b - with a one-piece lower head (“Ural”); 1 — connecting rod cover; 2 — connecting rod bolt; 3 — connecting rod; 4 — bearing separator of the lower head of the connecting rod and rollers; 5 — liners

The crankshaft receives force from the piston (via the connecting rod), converts it into rotational motion, and then transmits the torque to the transmission. In addition, other systems and mechanisms are driven from the crankshaft: gas distribution mechanism (GRM), oil pump (in four-stroke internal combustion engines), generator, cooling system pump, balance shafts. Depending on the number of engine cylinders and the design design, the crankshaft may have one or more elbows, each of which is formed by two cheeks and a connecting rod journal. Between the knees and along the edges of the shaft there are main journals supported on bearings.

Crankshafts are made composite or non-separable (one-piece). The type of bearings of its supports (main journals) depends on the lubrication system used. To improve the smooth operation of the engine (after all, only one stroke of the piston is working, and the rest - one for a two-stroke engine, and three for a four-stroke engine - require energy expenditure), the crankshafts have an external flywheel, massive cheeks and counterweights. In addition, many modern engines have special balance shafts driven by a gear train from the crankshaft.

Crankshaft of two-cylinder engine

b - solid (“Dnepr”); 1 — connecting rod with a one-piece lower head and a roller bearing; 2 - counterweight;

3D Motorcycle Engine

Four-stroke internal combustion engine. How it works?

Disassembling the Honda CBR929RR engine (part 1). The first part of a scary video of disassembling the engine of a Honda CBR929RR motorcycle. Someone has taken up residence in the engine and is growling, rattling, knocking. The bastards decided to find out who lives there and drive him out. To do this, we unscrewed all the attachments: covers, generator, drives, etc. The closer you get to “Alien”, the scarier it is...

The engine crankcase is made one-piece or with a split plane (longitudinal, transverse). In four-stroke engines, the crankcase (or sump) is usually a reservoir for oil draining from lubricated parts. Many engines share a common crankcase with clutch and gearbox. In two-stroke multi-cylinder engines, the crankcase volume of each cylinder must be separated from the others; this complicates the design of the crankcase when there are two or more cylinders.

Gas distribution in four-stroke internal combustion engines is controlled by a camshaft (or camshaft), which rotates twice as slow as the crankshaft. When rotating, the camshaft, with its protrusions (cams), interacts with pushers, which directly or through a transmission link (rocker arm, rocker) open the valves (intake and exhaust); their closure occurs under the action of valve springs. The periods of time when the intake and exhaust valves are open are called valve timing; they are coordinated with the piston strokes.

Valve timing diagram of a four-stroke engine

1 - opening of the intake valve; 2 - closing the intake valve; 3 - closing the exhaust valve; 4 — opening of the exhaust valve; angle “a” - valve overlap

To better fill the cylinder with the combustible mixture, the intake phase begins when the piston has not yet reached TDC. As the piston continues to move from TDC to BDC, it sucks in the combustible mixture through the open valve; they complete the intake after passing BDC, when part of the mixture enters the cylinder by inertia. Cleaning the cylinder from exhaust gases also begins at the end of the expansion stroke, when the piston has not yet reached BDC, but there is excess pressure in the cylinder. Then, as the piston moves from BDC to TDC, the piston pushes out the exhaust gases. The exhaust valve is closed after TDC to allow some of the exhaust gases to leave the cylinder by inertia. Thus, there is a period of time when both valves are open - this is called "valve overlap". Each four-stroke engine model has its own optimal valve timing, which is set at the factory by the profile of the camshaft cams. Some newer motorcycle engines have special devices that allow the valve timing to be changed depending on the crankshaft speed.

Modern four-stroke internal combustion engines use several types of timing belts: OHV, OHC, DOHC.

Schemes of gas distribution mechanisms

In the OHV design, the valves located in the cylinder head are driven from the “bottom” camshaft via pushrods, rods and rocker arms; the design does not ensure smooth operation of the mechanism at high crankshaft speeds. Engines with an OHC timing belt have an “overhead” camshaft that acts on the valve lifters through levers (rockers); the shaft is driven by a chain or toothed belt. Modern multi-valve heads with 4-5 valves per cylinder use two camshafts, each of which directly acts on the valve lifters with its cams (DOHC design). This design has a minimum of parts and, because of this, the inertia of the valve drive is reduced, which makes it possible to increase the engine crankshaft speed, and hence its power; DOHC type timing belts are becoming increasingly widespread.

OHV operation diagram

The camshaft is driven from the crankshaft by a gear, chain transmission or by means of a toothed belt. In the last two cases, the engines have chain (belt) tensioners and dampers.

For normal operation of the valve mechanism, there must always be a thermal gap (0.05–0.15 mm) between the valve stem and its drive. When there is no clearance, the valves do not close tightly, as a result of which they burn and fail. With an increased gap, they do not open completely (power is lost) and, in addition, they knock. Many engines of foreign motorcycles have timing belts with hydraulic compensators (operated by pressure in the lubrication system), which automatically maintain the required valve clearances. If such a system is not provided, the gap is adjusted during maintenance.

Four-stroke engines are structurally more complex than two-stroke engines, since they have an additional timing belt and lubrication system. However, since the 70s of the twentieth century, they have been predominantly used on motorcycles due to cleaner combustion and better efficiency. Currently, in developed countries, motorcycles with two-stroke engines have limited use - these are older models, sports motorcycles and mopeds; In the foreseeable future, particularly in Europe, the production of these engines is expected to cease completely due to the extremely negative impact on the environment.

Motorcycle engines most often have 1, 2 and 4 cylinders, although there are 3, 6 and even 10 cylinders. They have a variety of layouts: in-line (longitudinal and transverse), V- and L-shaped, horizontal opposed. The engine displacement of serial motorcycles usually does not exceed 1500 cm3, power is 150–180 hp.

Arrangement of cylinders in modern motorcycle engines

Engine lubrication and cooling systems

Lubrication of internal combustion engine parts is necessary to reduce friction between them and remove heat. It is carried out by motor oils that are resistant to high temperatures combined with low viscosity at low temperatures (for reliable engine starting). In addition, motor oils should not form carbon deposits during combustion and should not be aggressive towards rubber seals and plastic parts. Mineral oils (obtained from petroleum by distillation), semi-synthetic and synthetic oils are used for lubrication. Semi-synthetic oils are a mixture of high-quality petroleum and synthetic base components. Synthetic oils do not have a petroleum base; due to effective anti-friction additives, the service life of the engine is increased (compared to mineral oils), and it is easier to start at low temperatures. Despite the higher price, semi-synthetic and synthetic oils are increasingly used. Special motor oils are produced, and they differ for engines that differ in stroke (two- and four-stroke) and in the degree of boost. For Russian motorcycles with four-stroke engines, automobile oils of various viscosities are used, for two-stroke engines - MGD-14, or foreign analogues.

In four-stroke engines, three methods of supplying oil to friction surfaces are used: under pressure, splashing and gravity. Most friction pairs are lubricated under pressure generated by the oil pump. Other friction pairs are lubricated by oil mist, which is formed when oil droplets splash on the moving parts of the crank mechanism. And finally, the third group of parts is lubricated with oil flowing through special channels and gutters. The crankcase (sump) is usually an oil reservoir (the so-called “wet” crankcase - Fig. a).

Four-stroke engine lubrication systems

Some foreign motorcycles have a system with a “dry” sump (Fig. b), from which oil is first pumped out by one of the pump sections into a separate oil tank, and supplied under pressure to the friction surfaces by the other section. The tank can be located in different places: near the engine, at the rear wheel or in the front of the frame.

The oil level in all lubrication systems is controlled using a dipstick (with minimum and maximum level marks) or through a special inspection hole. Operating the engine with a low oil level is unacceptable.

The lubrication system contains an oil pump, an oil filter, valves (return and safety) and lines in the form of channels (tubes, drillings in parts).

Oil pumps for four-stroke internal combustion engines are of plunger and gear types.

Types of Oil Pumps

a - plunger; b - gear with external gearing; c - with internal gearing

The most widely used gear pump The gears are driven into rotation by the engine crankshaft or camshaft. The oil enters the inlet cavity of the housing, is captured by the gear teeth and is pumped to the outlet cavity. The most common filters are replaceable paper ones.

In two-stroke engines, the rubbing pairs are lubricated by oil present in the form of small droplets in the fuel vapor. Oil is mixed with gasoline either first in the tank (in a ratio of 1:25–1:50), or directly in the inlet pipe, where it is supplied in the required quantity by a special metering pump. The latest oil supply system is called a “separate lubrication system”; it is predominantly used on foreign two-stroke engines. In such systems, the oil supply at low loads is brought to a ratio of 1:200, which reduces exhaust smoke, reduces overall oil consumption and the formation of soot in the combustion chamber.

Two-stroke engine with separate lubrication system

1 - oil tank; 2 - carburetor; 3 — throttle cable separator; 4 — throttle handle; 5 — oil supply control cable; 6 — plunger dosing pump; 7 - hose supplying oil to the inlet pipe

Separately lubricated systems use plunger-type pumps driven by the crankshaft or engine transmission. The oil is stored in a special tank and flows to the pump by gravity. The design provides a low oil level indicator in the tank. The amount of oil supplied to the inlet pipe depends on the engine speed; in some designs there is another adjustment of its performance - from the position of the throttle handle, for which the pump is connected to it by a separate cable.

Cooling system

When fuel burns in an internal combustion engine cylinder, heat is released, part of which (about 35%) goes to useful work, the rest is dissipated into the environment. If heat dissipation is not effective enough, the parts of the cylinder-piston group overheat, and due to their excessive expansion, as well as violation of lubrication conditions, jamming and damage to the parts may occur. To prevent overheating, all motorcycle engines, regardless of stroke, have a cooling system - air or liquid.

Cooling systems for motorcycle internal combustion engines

Engine oil

Lubrication is necessary to ensure that excessive friction does not occur between engine parts. It is implemented using motor oils that have a stable structure against high temperatures and low viscosity at low levels. In addition, they do not form carbon deposits and are not aggressive to plastic and rubber parts.

Oils are mineral, semi-synthetic and synthetic. Semi-synthetics and synthetics are more expensive, but these types are preferred more, as they are believed to be healthier for the engine. Different types of oils are used for two-stroke and four-stroke engines. They also differ in the degree of forcing.

Motorcycle diagram

How energy is transferred to the wheel

The operation of a motorcycle engine is in many ways similar to that of a car engine. The fuel burned in the engine cylinders pushes the pistons (in the picture above), which rotate the crankshaft. In a gearbox, the rotational movement of the crankshaft is transmitted to the chain. It is she who turns the rear wheel. But a motorcycle also needs a gearbox: to reduce the too high rotation speed received from the engine. And finally, the rear wheel makes one full revolution per two revolutions of the crankshaft.

"Wet" and "dry" sump

Four-stroke engines use three methods of oil supply:

• gravity;
• splashing;
• supply under pressure.

Moreover, most of the rubbing pairs are lubricated under pressure from the oil pump. But there are also those that are lubricated by oil mist formed as a result of splashing of the crank mechanism, as well as parts to which oil flows through channels and gutters. In this case, the oil pan serves as a reservoir. In this case it is called “wet”.

Other motorcycles have a “dry” sump system, where one section pumps oil into the tank, and the other supplies it under pressure to the friction points.

In spirit-tactics, lubrication occurs with oil, which is found in fuel vapor. It is pre-mixed with gasoline, or it is supplied to the inlet pipe by a metering pump. This latter type is called the “separate lubrication system.” It is especially common on foreign engines. In Russia, the system is included in the engine of the Izh Planet 5 and ZiD 200 Courier motorcycles.

Bike diagram for a beginner

This section is intended to describe the scheme of motorcycle equipment for beginner lovers of two-wheeled horses. The following brief visual information will help you understand the simplest steel horses. This is exactly what the bikes of the 1960s looked like. from the world's leading manufacturers of similar products. Moreover, this applies to former motorcycle legends and modern brands of iron horses. Using this picture you can study the history of the structure of motorcycles.

The first number in the diagram shows the front shock absorber fork. However, you will not see the springs themselves in the front part of the motorcycle, since the latter are hidden under an iron casing called pants. Number 2 indicates the dashboard light indicator lamps. In older bike models they were installed directly on the top of the headlight. The third number is the speedometer.

Number 4 is represented by the front brake drive handle. 5 is a (gas) handle that changes the fuel supply level using the throttle. Number six indicates the clutch lever. 7 - gas tank. 8 - air purifier. This is exactly what his old samples looked like. Number 9 in the picture is represented by the rear shock absorbers. 10 — exhaust pipe (namely “muffler”).

Number 11 will show you the rear fork (swingarm). 12 is a chain (chain drive). Number 13 indicates the engine (its crankcases). 14 is represented by a leading star. 15 is the motor chain. Number 16 indicates the left crankcase (motor) cover. 17 - piston. 18 - cylinder (popularly referred to as “piston”). Number 19 on the motorcycle diagram shows the brake pads of the front wheel drum. Well, 20 is the front wheel drum itself.

Liquid cooling system

The option is similar to what is installed on cars. The coolant here is antifreeze, which is low-freezing (from minus forty to minus sixty degrees Celsius) and high-boiling (from one hundred twenty to one hundred and thirty degrees Celsius). In addition, antifreeze achieves an anti-corrosion and lubricating effect. Pure water cannot be used in this capacity.

Overheating of the cooling system can be caused by overload or contamination of the surfaces that dissipate heat. Also, individual elements in it may break, causing liquid to leak out. Therefore, the cooling operation must be constantly monitored.

How is a motorcycle designed and how does it work?

Like a car, a motorcycle “eats” gasoline to get energy for its movement. The significant difference between them is that a motorcycle has only two wheels. The engine's energy is transferred to the rear wheel. And although its power is often much less than that of a car engine, a motorcycle, thanks to its streamlined profile and lighter weight, can reach the same speeds as a car. In addition, motorcycles usually accelerate faster than cars and are more agile on narrow roads and off-road.

Supply system

Gasoline with an octane number of at least 93 is used as fuel for carburetor motorcycles.

Motorcycle engines have a power supply system that includes a fuel tank, valve, filter, air filter and carburetor. Gasoline is located in a tank, which in most cases is installed above the engine in order to flow by gravity into the carburetor. In other cases, it can be supplied using a special pump or vacuum drive. The latter can be found on two-stroke bikes.

The fuel tank has a cap with a special hole where air enters. In many foreign motorcycles, however, air enters through carbon tanks. And some have a lock on the lid.

The fuel valve prevents fuel leakage.

Air enters the carburetor through the air filter. The filter comes in three types.

1. In the compact oil type, air enters the center, turns 180 degrees and passes into the filter. At the same time, it is cleaned when the flow turns, where heavy particles settle in the oil. The engine of the Ural and Izh motorcycles is equipped with such a filter. However, other types, paper and foam, are used abroad.
2. Paper filters are disposable. They must be changed at every maintenance.
3. Foam filters are reusable - they can be washed and re-soaked with oil.

Sports motorcycles with engines of 250 cc and above today have a so-called “direct intake” system, where air is taken in from the front of the fairing, thereby increasing the filling of the cylinders at high speeds.

Opposite

A piston internal combustion engine with rows of cylinders positioned at an angle of 180 degrees relative to each other. Reaching the dead center of the opposing pistons occurs simultaneously (mirrored). Very similar to the V-twin engine, but the difference is in the degree of cylinder placement. Used by BMW and in our Urals and Dnieper. Pros: high torque, cylinders are well cooled, center of gravity is low. Cons: wide design and difficult to assemble (especially the gas distribution mechanism).

Our recommendation is to purchase original components. We cooperate with manufacturing plants Suzuki and Honda and supply contract spare parts that are tested by specialists. Write to our employees, they will help you choose the right part.

Carburetor and its types

This device prepares and doses the air-fuel mixture, which then goes into the cylinder. Modern carburetors come in three types:

• spool valves;
• constant vacuum;
• register.

All domestic engines, as well as the Ural motorcycle engine, have spool carburetors. The only exception is the Ural-Vostok, which has a constant vacuum carburetor.

In a spool-type carburetor, the throttle handle is connected to the spool. By acting on it, the air entering the motor is regulated. A conical needle is connected to the spool and enters the sprayer. When it changes, the mixture becomes richer or leaner. A fuel nozzle is installed on the sprayer. And together all the elements make up the dosing system.

In constant vacuum carburetors, the movement of the throttle handle is transmitted to the throttle valve, which is located closer to the outlet of the carburetor. The air in the chamber above the spool interacts with the carburetor mixing chamber. It turns out that the movement of the spool is controlled by the vacuum in the intake tract.

Register carburetors, which are equipped with many foreign single-cylinder four-stroke engines, such as Honda engines, combine the two previous types. It has two mixing chambers, where in one the spool is driven by the handle, and in the other by the vacuum in the mixing chamber.

FAQ

How is engine displacement measured?

Engine displacement is measured in cubic centimeters

(cm3), but in documentation it is often written in liters (l.). 1000 cubic centimeters equals 1 liter. The most accurate unit for measuring volume is cubic centimeters, since when the volume of a car engine is indicated in liters, it is rounded to a whole number after the decimal point. For example, the volume is 2.4 liters. equal to 2429 cm3.

What is the formula for engine cylinder displacement?

The working volume of the engine cylinder is equal to the product of Pi (3.1415) by the square of the radius of the base and the height of the piston stroke in it. The formula itself for the volume of an internal combustion engine cylinder in cubic meters. centimeters looks like this: Vwork = π⋅r²⋅h/1000

How to measure car engine displacement?

Engine volume is the sum of the working volumes of all its cylinders; accordingly, you must first find out what the volume of one cylinder is, and then multiply by their number. The volume of a cylinder is calculated by multiplying the height by the square of the radius and the number “Pi”. But in order to measure exactly the working volume of a cylinder in an engine, you need to take the length of the piston stroke from BDC to TDC as the height, and the radius can also be measured with a ruler, having first found out the diameter of the cylinder. This measurement method is only possible when the head is removed or the parameters are known.

Launch

In order to start a cold engine, a rich mixture is needed. Some carburetors have a float stopper in the chamber for this purpose. When its rod is pressed, the fuel level in the chamber rises sharply to a level above the permissible level. Because of this, fuel begins to flow into the intake manifold. And some of the fuel leaks out. For some time now, however, carburetors have been designed in such a way that vapors do not escape outside. Such designs involve the use of an enrichment mixture, which is an air damper or another fuel channel. It is used instead of a drowner.

Recently, four-stroke motorcycle engines often have an electrically controlled fuel injection system. It consists of an electrically driven fuel pump, a battery, electromagnetic injectors, an electronic control unit, which is connected to various sensors, and a distribution pipeline.

There are also engine control systems where the control of the power supply and ignition systems are combined, which increases the efficiency and at the same time the power of the unit.

The main malfunction of the power system, due to which a motorcycle engine may need to be repaired, is a reduction or even cessation of fuel supply due to a blockage. To avoid this, use a fuel filter. In addition, it is necessary to monitor the condition of the air filter and the tightness of the pipes.

DUCATI MONGREL

Rodsmith Customs

Melbourne native Craig Rodsmith works out of a small workshop north of Chicago. In winter it’s like a refrigerator, and in summer it’s like an oven. However, Rodsmith, with his appearance, accent and manner of speaking reminiscent of Mad Max, feels at home here. “I love everything Italian,” the master admits, “so one day I decided to build a bike based on the 1955 Moto Guzzi V8 with a large fairing of a characteristic shape made of hand-knocked and polished aluminum. At that time, I had almost no money, and my cat and I ate canned tuna. The electricity in my apartment was turned off. So in 2016 I took this bike to the Handbuilt Motorcycle Show, where Bobby Haas promptly bought it for his Haas Moto Museum in Dallas. It changed my life."

The master is most proud of the fact that he did without computerized elements during the assembly process. “All Moto Guzzi panels are handmade on an English wheel using a hammer and a metal blank.” His Ducati Mongrel is the first bike he has built for himself in a long time. The name Mongrel (English: "mongrel cross") hints that the bike is not of pure blood: it combines the Ducati M900 Monster two-valve V-engine and the single-sided swingarm frame of the Ducati 948 of the early 1990s. Rodsmith added a supercharger and nitrous oxide injector. The polished NOS canister hanging from the rear of the subframe adds another gauge, and the gauges look cool, Rodsmith says. And he considers himself lucky because he builds custom motorcycles for a living.

Exhaust system

The exhaust system consists of a cylindrical exhaust channel, a pipe and a muffler. In two-stroke engines, efficiency and power directly depend on the size and shape of the system parts. Therefore, they use exhaust systems on each cylinder separately. They have a resonator, a pipe and a muffling nozzle.

In four-stroke engines, the exhaust is controlled by valves in the gas distribution system, so resonance does not play a special role in them. In them, usually all pipes are reduced to a single muffler.

On some motorcycles, the exhausts are equipped with catalytic converters that reduce the toxicity of emissions (they are installed, for example, on engines from Honda and other Japanese manufacturers). Such devices were developed as a result of increasingly stringent exhaust gas requirements in the European Union, the USA and Japan. In order to prevent the backflow of mixture from the cylinders at idle and low crankshaft rotation, the exhaust systems of many motorcycles are equipped with special power valves.

Motorcycle driving theory

Are you going to learn how to ride a motorcycle? For this reason, did you go to a driving school to gain initial skills and learn the rules of the road in order to obtain a driver’s license of category “A” or “A1”? But for some reason, you need more knowledge and simple explanations that will help you learn how to ride a motorcycle easily? Our online publication offers you a small “Step by Step” guide, with the help of which anyone can understand how to quickly learn how to operate a motorcycle.

A motorcycle, just like a car, attracts a lot of attention. Many would dream of mastering it, but they mistakenly believe that driving a motorcycle is difficult and dangerous. In fact, it is quite simple, and if you follow all safety precautions and traffic rules, a motorcycle becomes no more dangerous than a car.

However, a motorcycle is still considered a vehicle with an increased risk of getting into an accident. But despite this, our tips will help you make the process of learning and gaining initial experience of driving motorcycles more enjoyable and comfortable.

Calculation of internal combustion engine volume with a calculator

To calculate the volume of the engine you are interested in, you need to enter 3 numbers in the appropriate fields - the result will appear automatically. All three values ​​can be found in the car’s passport data or technical data. characteristics of a particular part, or a caliper will help determine what piston volume.

Thus, if, for example, you find that the volume is 1598 cm³, then in liters it will be designated as 1.6 liters, and if the number is 2429 cm³, then 2.4 liters.

Long-stroke and short-stroke piston

Also note that with the same number of cylinders and engine displacement, the cylinder diameters, piston strokes and power of such engines may also be different. An engine with short-stroke pistons is very power hungry and has low efficiency, but achieves great power at high speeds. And long-stroke ones are located where traction and efficiency are needed.

Therefore, the question “how to find out engine size by horsepower” can be given a firm answer - no way. After all, although horsepower has a connection with engine volume, it will not be possible to calculate it from them, since the formula for their relationship also includes many different indicators. So the cubic centimeters of an engine can be determined solely by the piston parameters.

To make it easier to move

The spring suspension system is installed on both wheels of the motorcycle. It protects the motorcyclist and the engine from impacts due to uneven roads.

Front wheel suspension

Shock-absorbing springs are hidden inside hollow oil-filled forks. These springs reduce shock and vibration.

Rear wheel suspension

The rear shock absorption mechanism is attached to the motorcycle frame itself - one on each side of the wheel.

Two-stroke engine gives more power

Cars usually use four-stroke engines. Their operating cycle consists of four parts: mixture intake, compression, combustion and exhaust. This requires two movements of each piston back and forth. A two-stroke motorcycle engine (picture above) performs all the same operations in one complete back-and-forth motion of the piston: As the piston rises (left picture), intake and compression occur. And when it goes down, combustion and exhaust (right picture). Therefore, theoretically, at the same speed, that is, the same number of revolutions per minute, a two-stroke engine should be twice as powerful as a four-stroke engine. However, in practice, due to the size of the two-stroke engine and the increased friction in it, its advantages are not so great. And yet, the power of a two-stroke internal combustion engine is approximately 1.5 times higher than the power of a four-stroke one.

Let's briefly consider the main components of a motorcycle:

The clutch is a lever located on the left side of the motorcycle. It is very easy to operate, just a simple finger press is enough. The clutch is responsible for engaging the mechanism and facilitating smooth gear shifting.

All motorcycles are equipped with cylinders, but the number of cylinders may vary. There are models with the number of cylinders from one to six. This device is cooled with a special liquid to prevent overheating in the event of unusual use of the motorcycle in emergency situations.

Any vehicle, including a motorcycle, must have a brake. It is very important because it slows down the speed of movement, if necessary. There are two types of brakes. The first is the front brake, which is located on the right side of the motorcycle. He is responsible for stopping the front wheel. The second is the rear brake, designed to stop the rear wheels of the motorcycle. This is a foot brake. In case of an emergency on the road, if it is necessary to stop the vehicle suddenly, it is recommended to use both brakes simultaneously.

A properly functioning suspension guarantees a comfortable ride. It provides a stable and smooth ride, softens shocks on bad roads.

A gas tank is a container where fuel for running a motorcycle is stored.

Gear shifting is a pedal for changing speeds, controlled by pressing the foot.

The spark plug acts as an igniter to start the engine.

The ignition switch is where the key that starts the motorcycle engine is located.

The steering wheel is a means of controlling a motorcycle, with its help it is possible to turn left and right.

The throttle increases the speed of the motorcycle. It is operated manually by turning a lever.

Side mirrors play an important role when driving a motorcycle. They allow the driver to see the situation behind him without turning around or losing control of the road ahead. To have a good view behind you, you need to install the mirrors at right angles and always keep them clean.

Now that you have become familiar with the purpose and functioning of the main parts of a motorcycle, you can start riding it for the first time! Have a safe ride!